KIT BOXES

A Kit Box includes all parts needed to install a Dynamic Trim Control System with one pair of fast-acting interceptors. There are four different Kit Boxes, one for each interceptor model.

Any base installation can be expanded with up to two extra pairs of Series S interceptors, thus allowing a total of six interceptors without any need for additional connectors or power supply.

<

SPECIFICATIONS

Model
Width
Depth
Height
Weight
KB300-S
680 (26.8)
156 (6.1)
274 (10.8)
7.0 (15.3)
KB450-S
680 (26.8)
156 (6.1)
274 (10.8)
8.5 (18.7)
KB600-S
980 (38.6)
156 (6.1)
274 (10.8)
10.6 (23.3)
KB750-S
980 (38.6)
156 (6.1)
274 (10.8)
11.7 (25.8)

ORDERING DATA

Model
Part No.
KB300-S
2011145
KB450-S
2011146
KB600-S 2011147
KB750-S 2011148

SMART RIDE CONTROLLER

Zipwake’s unique 3D controls provide the driver with user-friendly, intuitive and precise control of running trim, heel or heading that is unmatched. Integral, high- frequency GPS, 3D gyro sensors and a robust motion controller all come as standard along with a sunlight readable color display.

Push the AUTO BUTTON - and GO!

The system automatically eliminates uncomfortable and dangerous boat pitch and roll dynamically. It also minimizes wave resistance and saves fuel.

FULLY AUTOMATIC
INTERNAL GPS & 3D GYRO
WATERPROOF BY DESIGN
SUNLIGHT READABLE
AUTO DIMMING NIGHT MODE
  • Fully automatic
    • Dynamic pitch and roll control

    • Steering enhancement
  • Built-in GPS and motion sensors
  • Unique and intuitive 3D controls
  • Sunlight readable color display
  • Instant state user feedback
  • Auto power on/off via ignition key sense
  • Full range of electrical interfaces
  • NMEA 2000
  • Waterproof
  • Auto dimming / night mode
  • Upgradable via USB stick
  • Up to four control panels in the system
  • Surface or flush mount

SPECIFICATIONS

Model
CP-S
Display
2.4’’ Transflective color TFT, 320 x 240 pixels, double-sided, anti-reflection coated window
Internal sensors
5 Hz GPS, 3D Gyro, 3D Accelerometer, Ambient light
Supply Voltage
12 - 32 V DC
Power Consumption
10 W max
Operating Temperature
-20° to +85°C (-4° to +185°F)
Storage Temperature
-40° to +90°C (-40° to +194°F)
Waterproof Rating
IP67 / IP64 (front / back)
Compass Safe distance
0.5 m (1.7 ft)
Compliance
CE, FCC
Weight
0.22 kg (0.49 lbs)
Mounting
Flush or surface

INTERFACES

  • I-BUS IN (CAN bus)
  • I-BUS OUT (CAN bus)
  • NMEA 2000
  • External GPS (NMEA 0183 / RS232 auto baud-rate sensing)
  • Key Sense
  • USB Device Port (Type A)
  • USB Host Port (Type B)

ORDERING DATA

  • Included in Kit Boxes
  • Available as an Accessory
  • Available as a Spare Part
Model
CP-S
Part No.
2011238
 
with Standard Cable 7 m

STATE OF THE ART INTERCEPTORS

Series S incorporates a state-of-the-art family of four durable, fast-acting interceptors. This first-ever modular design made for mass production makes the interceptors durable, affordable and perfectly adapted to any planing or semi-planing boat between 6m and 18m (20-60ft).

All components have been meticulously engineered to withstand impact and avoid water ingress, minimizing the risk of costly maintenance and downtime. Interceptor or blade actuation takes place by way of a calibration-free submersible electric servo within the interceptor unit. Its natural water cooling provides excellent working conditions for the brushless DC servo motor, which runs on 12-32 volts. The blade stroke takes 1.5 seconds, outperforming conventional trim tabs by at least a factor of 5.

Installation is made easy with an integral mounting plate and the option of a concealed or above-waterline, self-sealing, thru-hull cable fitting. The preferred mounting option is achieved by simply routing the servo cable differently. Each interceptor comes with the thru-hull cable fitting, cable covers and a practical drill template.

OUTBOARD MOUNT
MODULAR DESIGN
FAST ACTUATION
CALIBRATION FREE
NO CORROSIVE MATERIALS
  • True outboard mount
  • Modular design
  • Fast actuation
  • Submersible servo units
  • Brushless 12-24V DC servo
  • High-precision positioning
    • Calibration free
  • Durable and accessible
  • Integrated mounting plate
  • Thru-hull fitting options
    • Above waterline
    • Concealed behind interceptor
  • No corrosive materials

SPECIFICATIONS

Model
IT300-S / IT450-S / IT600-S / IT750-S
Length
300 (12) / 450 (18) / 600 (24) / 750 (30) / mm (in)
Weight
2.1(4.6) 2.8 (6.2) 3.5 (7.7) 4.0 (8.8) kg (lbs)
Max. Boat Speed
60 knots
Blade Stroke
30 mm (1.2 in)
Blade Rate
20 mm/s (0.8 in/s)
Thru-Hull Cable Fitting
Concealed or above waterline
Servo actuator
SU-S
Cable Length
3 m (10 ft), extendable up to 6 m (20 ft)
Cable Material
PUR
Connector
M12 5-pin circular
Connector Diameter
14.5 mm (0.57 in)
Supply Voltage
12 - 32 V DC
Power Consumption
25 W max
Operating Temperature
0° to +40°C (+32° to +104°F)
Storage Temperature
-40° to +90°C (-40° to +194°F)
Waterproof Rating
IP68 5 m (16 ft)
Compliance
CE, FCC
Connector Diameter
14.5 mm (0.57 in)

ORDERING DATA

  • Included in Kit Boxes
  • Available as an Accessory
  • Available as a Spare Part
Model
IT300-S / IT450-S / IT600-S / IT750-S
Part No.
2011232 / 2011233 / 2011234 / 2011235
 
--- with Cable 3 m and Cable Covers ---

DISTRIBUTION UNIT

The Distribution Unit supplies the system with power and can accommodate up to six Series S interceptors. The unit is connected to the main control panel. It is robust, waterproof, oil resistant and ignition protected for mounting in an engine room. The power cable is included for easy connection to a battery. The distribution unit has built-in electrical protection, including its own protection fuse.

SPECIFICATIONS

Model
DU-S
Supply Voltage
12 - 32 V DC
Power Consumption
0.1 W max
Protection Fuse
10 A ATO
Power Cable Length
4 m (13 ft), Diameter 9 mm (0.35 in), 12 AWG
Operating Temperature
-20° to +85°C (-4° to +185°F)
Storage Temperature
-40° to +90°C (-40° to +194°F)
Waterproof Rating
IP67 with cables and/or protective caps mounted
Oil resistance
Common engine fluids
Compliance
CE, FCC, SAEJ1171 Ignition Protected
Weight
1.0 kg (2.2 lbs) including the power cable

CONNECTORS

  • Six interceptor connections
  • I-BUS OUT (power and CAN bus to control panels)
  • 2-lead power cable

ORDERING DATA

  • Included in Kit Boxes
  • Available as an Accessory
  • Available as a Spare Part
Model
DU-S
Part No.
2011239
 
with Power Cable 4 m

EXTERNAL GPS ANTENNA

The Zipwake external GPS antenna is a 5Hz, 20-channel receiver with excellent reception that provides accurate and rapid vessel position and speed updates. Vessel speed is necessary input for the Zipwake’s automatic motion controller. The antenna has a rugged construction, is fully waterproof and can be pole or surface mounted on any vessel.

The external GPS is optional and intended to be used when no other strong GPS signal is available for the Zipwake system, e.g. when the vessel has just one helm station with a shielding top (roof) and lacks other accessible GPS sources. In this case, the external GPS antenna is a good solution. Its 5 m cable can be extended up to 15 m using Zipwake extension cables. It connects easily to the connector marked EXT GPS on the back of the control panel. The external GPS can be connected to any control panel installed in the system.

SPECIFICATIONS

Model
GPS
Connectors
M12 5-pin circular
Cable Material
White PVC
Cable Length
5 m (16 ft) extendable to max 15 m (49 ft)
Supply Voltage
5 V DC ±5%
Power Consumption
0.28 W, 55 mA (average)
Protocol
NMEA 0183 / RS232
NMEA Sentences
RMC, VTG, GGA, GSA, GSV, GLL
Baud Rate
38400
Update Rate
5 Hz
Number of Channels
20
Average Time to First Fix
Hot start 6 s, Warm start 38 s, Cold start 42 s
Operating Temperature
-30° to +85°C (-22° to +185°F)
Storage Temperature
-40° to +95°C (-40° to +203°F)
Waterproof Rating
IP67
Compliance
CE, FCC
Weight
0.065 kg (0.14 lbs) without cable and connector
Mounting
Flush or pole

PINOUT

PIN1
+5V
PIN2
RX (to GPS)
PIN3
GND
PIN4
not connected
PIN5
TX (from GPS)

ORDERING DATA

  • Available as an Accessory
Model
GPU
Part No.
2011240
 
with Cable 5 m and Mount Kit

CABLES

The Standard Cable is used to connect the main control panel to the distribution unit, usually located on or near the transom. This cable is also used to connect the main panel to the next panel, e.g. the flybridge. The Standard Cable can be extended by using any of the available extension cables. The servo unit cable can be extended using 1.5 m or 3 m extension cables. The total servo cable length must not exceed 6 m (20 ft).

SPECIFICATIONS

Model

Length
Weight
SC7-M12
Standard
7 (23)
0.38
0.84
EC1.5-M12
Extension
1,5 (5)
0.10
0.22
EC3-M12
Extension
3 (10)
0.18
0.40
EC5-M12
Extension
5 (16)
0.28
0.62
EC10-M12
Extension
10 (33)
0.56
1.23


m (ft)
kg
lbs

ORDERING DATA

  • Included in Kit Boxes
  • Available as an Accessory
  • Available as a Spare Part
Model
Part No.
SC7-M12
2011257
EC1.5-M12
2011258
EC3-M12
2011259
EC5-M12
2011260
EC10-M12
2011261

CABLE COVER

The thru-hull cable fitting of Series S interceptors can either be concealed behind the interceptor or positioned above the waterline. If the above-waterline mount is preferred, three parts are available to protect the cable: thru-hull cover, cable cover and a cable cover extension.

These parts are available as a cable cover kit to provide flexible routing of the cable on the transom.

SPECIFICATIONS

Model
CC-S
Items in kit
1 x Thru-hull cover
1 x Cable cover
1 x Cable cover extension
Weight
0.18 kg (0.26 lbs)

ORDERING DATA

  • Available as an Accessory
  • Available as a Spare Part
Model
CC-S
Part No.
2011071
comes with each Interceptor, part numbers 2011232-2011235

SERVO UNIT

The Series S submersible electrical Servo Unit fits inside the interceptor, where it drives with precision the mechanism that provides linear motion to the interceptor blades. The unit is fast-acting, durable, calibration free and easy to install or replace. It comes with a rugged 3m cable with self-sealing thru-hull fitting.

SPECIFICATIONS

Model
SU-S
Servo Motor Type
Brushless DC with Hall sensors
Supply Voltage
12 - 32 V DC
Power Consumption
25 W max
Operating Temperature
0° to +40°C (+32° to +104°F)
Storage Temperature
-40° to +90°C (-40° to +194°F)
Waterproof Rating
IP68 5 m (16 ft)
Compliance
CE, FCC
Cable Length
3 m (10 ft), extendable up to 6 m (20 ft)
Cable Material
PUR
Connector
M12 5-pin circular
Connector Diameter
14.5 mm (0.57 in)
Weight
0.75 kg (1.7 lbs) including cable

ORDERING DATA

  • Available as an Accessory
Model
SU-S
Part No.
2011230
 
with Cable 3m

CONTROL PANEL ALU FRAME

The control panel of Series S comes with a black frame and a wheel cap with a chrome appearance. A conversion kit is available for those who prefer a brushed aluminum appearance. The kit includes simple instructions that make changing an easy task.

SPECIFICATIONS

Model
CP-S ALU FRAME
Surface appearance
Brushed aluminum
Items in kit
1 x Frame, 1 x Wheel cap, 1 x Instructions
Weight
0.03 kg (0.06 lbs)

ORDERING DATA

  • Available as an Accessory
Model
CP-S ALU FRAME
Part No.
2011281

THE SYSTEM

Zipwake Series S, the world’s first inexpensive dynamic trim-control system, incorporates a state-of-the-art family of durable, fast-acting interceptors. The system is fully automatic. It significantly enhances the boat’s performance, fuel economy, comfort and safety when accelerating, turning or running in a seaway.

  • Dynamically eliminates uncomfortable and dangerous boat pitch and roll.
  • Automatically minimizes wave resistance and saves fuel.
  • Built-in quality, simplicity and easy expansion, yet still affordable.

DYNAMIC TRIM CONTROL SYSTEM SERIES S

RECOMMENDED RETAIL PRICES - 2015


Model Part No. Description EUR
KB300-S 2011145 Kit Box 300 S 1 289
KB450-S 2011146 Kit Box 450 S 1 384
KB600-S 2011147 Kit Box 600 S 1 479
KB750-S 2011148 Kit Box 750 S 1 574

Model Part No. Description EUR
CP-S 2011238 Control Panel S with Standard Cable 7 M 545
DU-S 2011239 Distribution Unit S with Power Cable 4 M 121
IT300-S 2011232 Interceptor 300 S with Cable 3 M & Cable Covers 329
IT450-S 2011233 Interceptor 450 S with Cable 3 M & Cable Covers 376
IT600-S 2011234 Interceptor 600 S with Cable 3 M & Cable Covers 424
IT750-S 2011235 Interceptor 750 S with Cable 3 M & Cable Covers 471
EC1.5-M12 2011258 M 12 Extension Cable 1.5 M 17
EC3-M12 2011259 M 12 Extension Cable 3 M 30
EC5-M12 2011260 M 12 Extension Cable 5 M 42
EC10-M12 2011261 M 12 Extension Cable 10 M 62
SC7-M12 2011257 M 12 Standard Cable 7 M 48
CP-S ALU FRAME 2011281 Control Panel S Alu Frame 24
CC-S 2011071 Cable Cover S 17
SU-S 2011230 Servo Unit S with Cable 3 M 268
IT300-S FRONT 2011252 Interceptor 300 S Front 104
IT450-S FRONT 2011253 Interceptor 450 S Front 138
IT600-S FRONT 2011254 Interceptor 600 S Front 173
IT750-S FRONT 2011255 Interceptor 750 S Front 208
GPU 2011240 Global Positioning Unit with Cable 5 M & Mount Kit 234

Terms

Terms Zipwake is manufactured in and delivered from Sweden. All prices are ex works and excluding VAT. Prices are based on exchange rate: EUR 1 = SEK 9,25. If exchange rate differs more than ±5% prices will be adjusted accordingly.

MADE IN SWEDEN

DEALERS